Dishwasher Filter Cleaning by Brand

Find and clean the filter in Bosch, Frigidaire, GE, KitchenAid, Maytag, Samsung and Whirlpool dishwashers, with steps that suit each design.

8 min read2 viewsDishwasher Filter Cleaning by Brand
— · 0 votes
Contents
  1. Why the filter matters in every brand
  2. Find the filter in your dishwasher
  3. Remove the filter without forcing it
  4. Rinse and scrub the filter parts
  5. Put the filter back the right way
  6. How often to clean, by use
  7. Brand notes at a glance
  8. When to call a technician
  9. Dishwasher filter cleaning questions
  10. Where is the filter on a Bosch dishwasher?
  11. How do I remove a GE dishwasher filter?
  12. Does a Samsung dishwasher filter come apart?
  13. How often should I clean a Whirlpool dishwasher filter?
  14. Why does my dishwasher have standing water after cleaning the filter?
  15. Can I put dishwasher filter parts in the dishwasher?

Dishwasher filter cleaning by brand follows one shared routine: remove the filter, rinse off food and grease, and put it back seated correctly. The brands differ in where the filter sits and how it comes apart, so check your owner's manual before you twist anything. A clean filter keeps water moving and stops debris from being recirculated onto your dishes.

  • Every brand uses the same core steps: locate the filter, unlock it, rinse it, and refit it fully.
  • Most modern filters lift out without tools, but some have a locking ring or a two-part stack.
  • Rinse under warm running water and scrub gently; avoid harsh cleaners on plastic parts.
  • A filter that is not seated flat can cause poor washing and standing water.
  • Check the filter often if you rinse little or wash greasy loads.

Why the filter matters in every brand

A dishwasher filter traps food scraps so they do not spray back onto clean dishes. Water passes through the mesh while particles stay behind, and the pump keeps circulating the same water. When the mesh clogs, water flow drops and dishes come out gritty.

Each brand uses the same basic idea but shapes the filter differently. Bosch and KitchenAid models often use a cylindrical filter with a flat screen underneath. GE, Whirlpool and Maytag dishwashers often use a round filter you twist to unlock. Samsung and Frigidaire designs vary by model, so the owner's manual filter location is the safest guide.

Cleaning the filter is a short job you can do at the sink. You do not need special tools beyond a soft brush and warm water. The steps below apply across brands, with notes on what changes between them.

Find the filter in your dishwasher

The filter sits at the bottom of the tub, under the lower spray arm. Empty the bottom rack and pull out the lower basket so you can reach the floor of the machine. Look for a round or oval cover with a handle or a mesh cylinder.

Bosch and KitchenAid filters sit in a recessed well near the center. GE, Whirlpool and Maytag filters are near the front or center and often have a twist-lock ring. Samsung and Frigidaire filters may sit behind a small cover that lifts off first.

If you cannot see the filter, the owner's manual filter location diagram settles it. The manual also shows whether your model has one filter part or two. Do not pry at the tub floor with a knife, because plastic parts crack easily.

Remove the filter without forcing it

Most filters release with a quarter turn counterclockwise, then lift straight up. Some Bosch and KitchenAid models need the cylindrical mesh pulled off first, then the flat screen below. Hold the parts over the sink so loose food does not fall back into the tub.

A filter that will not turn may be held by a locking tab. Press the tab or lift the handle before turning, and stop if the plastic flexes sharply. Forcing a stuck filter can break the housing, which needs a service visit to repair.

Frigidaire and Samsung filters sometimes come apart in two pieces. Note how the pieces fit together before you separate them. Setting the parts in the same order on a towel makes reassembly simple.

Rinse and scrub the filter parts

Rinse each filter piece under warm running water to loosen food and grease. Use a soft brush or an old toothbrush to work debris out of the mesh. Scrub both sides of the screen, because grease collects on the underside too.

For greasy film, a drop of dish soap helps cut the coating. Avoid abrasive pads and strong chemical cleaners on plastic mesh, since they scratch or cloud it. A scratched filter traps particles more easily and is harder to rinse clean.

Check the mesh against a light to spot blocked holes. Hold the part up and look through it; light should pass evenly. Rinse again if any area stays dark or coated.

Put the filter back the right way

Seat the flat screen first, then the cylinder or cover on top, matching the marks or arrows. Turn clockwise until the part stops or clicks into place. A filter that sits proud of the tub floor is not locked in.

Run a short cycle and check for standing water or a grinding sound. Standing water often means the filter is loose or the seal is misaligned. Re-seat the parts and try again before calling for service.

Each brand marks alignment differently, so follow the manual for your model. Bosch and KitchenAid parts often have a small arrow that lines up. GE, Whirlpool and Maytag rings usually click when the lock engages.

How often to clean, by use

Clean the filter when you see food debris on the mesh or dishes feel gritty after a cycle. Heavy use with greasy pans calls for a rinse more often than light use with pre-rinsed plates. There is no single schedule that fits every kitchen.

A quick rinse under the tap takes little effort and prevents buildup. A deeper scrub with a brush handles greasy film that water alone leaves behind. Between deep cleans, a fast rinse after each load keeps the mesh clear.

If dishes stay wet or the machine smells, check the filter before assuming a mechanical fault. A clogged mesh restricts flow and traps odor. Cleaning it is the first step in any troubleshooting routine.

Brand notes at a glance

The table below sums up where to look and how each brand's filter typically releases. Designs change between models, so treat it as a starting point and confirm with your manual. The steps for rinsing and refitting stay the same across brands.

Bosch and KitchenAid filters often come in two parts and need the cylinder lifted off first. GE, Whirlpool and Maytag models often use a single twist-lock filter near the center. Samsung and Frigidaire designs vary, so check the manual diagram before pulling.

Whatever the brand, avoid forcing a stuck part and avoid harsh cleaners. A soft brush, warm water and a firm but gentle hand protect the mesh. Seating the filter flat at the end matters as much as cleaning it.

BrandWhere to lookHow it releases
BoschCenter well, two partsLift cylinder, then screen
KitchenAidCenter well, two partsLift cylinder, then screen
GECenter or front, round filterQuarter turn counterclockwise
WhirlpoolCenter, round filterQuarter turn counterclockwise
MaytagCenter, round filterQuarter turn counterclockwise
SamsungBehind a small coverLift cover, then filter
FrigidaireVaries by modelCheck manual diagram

When to call a technician

A cracked filter housing or a broken locking ring needs a trained specialist. Plastic parts inside the tub are easy to damage and hard to replace without the right part. Stop and book service if a part cracks during removal.

Persistent standing water after a clean filter points to a drain problem. A grinding pump or a machine that will not fill also goes beyond filter cleaning. These faults need a technician who can test the pump and drain system.

Keep the owner's manual with the model number handy for any service call. The manual lists the correct replacement filter for your model. Using the wrong part can cause leaks or poor washing.

Dishwasher filter cleaning questions

Where is the filter on a Bosch dishwasher?

The Bosch filter sits in a recessed well at the bottom center of the tub, under the lower spray arm. It usually comes in two parts: a cylindrical mesh and a flat screen below. Lift the cylinder off first, then remove the screen.

How do I remove a GE dishwasher filter?

The GE filter sits near the center or front of the tub floor and releases with a quarter turn counterclockwise. Lift it straight up once it turns freely. If it resists, check the manual for a locking tab before turning harder.

Does a Samsung dishwasher filter come apart?

A Samsung filter often comes apart in two pieces under a small cover at the tub floor. Lift the cover, then separate the parts and note their order. Check the manual diagram for your model, since designs differ.

How often should I clean a Whirlpool dishwasher filter?

Clean the Whirlpool filter when the mesh shows food debris or dishes come out gritty. Heavy use with greasy loads calls for more frequent rinsing than light use. A quick rinse after each load keeps buildup down.

Why does my dishwasher have standing water after cleaning the filter?

Standing water after a filter clean often means the filter is not seated flat or the seal is misaligned. Re-seat the parts and run a short cycle to check. If water remains, the drain system may need a technician.

Can I put dishwasher filter parts in the dishwasher?

Filter parts are best rinsed and scrubbed by hand at the sink. A soft brush and warm water remove food and grease without stressing the plastic. Harsh cleaners and abrasive pads can scratch the mesh.

Read next

Latest articles